Adhesive Lined
2009
 |
| No items matching your keywords were found. |
Adhesive Lined
Save Money By Repairing Your Damaged Fly Line
How many times have you planned a fantastic day of fishing only to find that somehow the fly line got caught andten damaged as you tried to free it. Maybe it got wrapped around a sharp rock or all tangled in a nearby tree. Perhaps it even got snagged on your fishing-reel spool and the frame?
A problem like this can easily curtail your fishing trip. But it doesn't have to if you follow some of my tips on repairing fly lines that have had their coatings shredded slightly or nicked at some point.
And because new lines are so expensive at roughly $70 for a new one it makes sense to try and repair the line first.
There are two main problems with having a damaged core. The first one problem is the distraction and annoyance you feel when your fingers run over the damaged section when you cast. Secondly, when your line has lost its integrity it can take on water, which can make the line behave oddly usually making it sink.
A simple and straightforward solution for non-PVC lines is to use an adhesive to rejoin the damaged ends of the core and the coating back together again.
Although the fixing may eventually buckle and crack because of the flexing of the fly line over time, this temporary fix can be enough to salvage your line for a few more fishing trips.
- Gel type super glues and compound adhesive create the best results.
- Make sure that the adhesive you apply covers all the damaged area completely
- Keep the coating relatively thin.
- A toothpick, with its fine slightly flexible tip is an excellent tool for applying the adhesive.
- Any excess can be wiped away with a moistened finger.
- Once the adhesive has been applied push the two ends together and hold the surfaces together to give the glue time to bond effectively.
Once you've made good the repair you must let the line dry completely before using it again otherwise your hard work will have been in vain.
If you are using a PVC fly line, the process is a little more complicated and difficult, because of the need to use a heat-shrink tube to cover the damaged section.
This is kind of sleeve is the sort of tubing you often get you to attach a braided loop the end of the fly line. It's also the kind of thing that you could pick up in a hardware or electrical store.
When you're doing this repair the most serious thing that can go wrong is applying heat carelessly and damaging intact portions of your fly line.
All you need to do is apply a piece of tubing that just larger than your line.
- Cut a section of tube that is about an inch longer than the damaged portion of line that needs repairing.
- Carefully slide the tube over the damaged area then whole league section to be repaired over a normal tungsten light bulb.
- The gentle heat from the bulb is just enough to heat the sleeve but not melt your existing coating - or burn your fingers.
- This process causes the sleeve to shrink fit over the damaged part and you can very carefully trim off any excess with a small sharp craft knife.
- Smooth off the join using a tiny soft pieces along the edges.
TIP: If you're not sure how this process is going to turn out you can always use a test portion taken from the very end of your line and practice with that rather than trying to do the fix right in the middle.
So now you have enough information to minimise the damage and keep your fly line in operation for a bit longer. Just try not to concentrate too much with your fingertips as inevitably you will still feel the repair.
Happy fishing,
John
About the Author
John Reece is a freelance writer for www.helpfuladviceonline.com and he has just published "Get your fly on - the ultimate guide to fly fishing".
how to line a dresser drawer?
i have looked all over for drawer liner to line my unborn nephews dresser drawer. the only thing i could find was liner for kitchen cabinets. so i bought some of that. the self adhesive kind but it wouldnt stick because there was no primer on it, it was just raw wood. i didnt want to go through priming all the drawers so i decided maybe wallpaper would be better and easier. what do people usually use to line dresser drawers and how do you do it on raw wood?
My mother in-law taught me to use freezer paper. It comes in nice wide rolls that will fit the depth of most drawers. Just cut a bit more from the roll than you need and fold the edges under. There's no need to attach it to the drawer itself, since it is stiff enough to stay put. You could probably use unpasted wallpaper too. I wouldn't use any sort of adhesive as it would make the paper difficult to remove if it became torn or stained.
How to Glue a Wood Chair : How to Put a Disassembled Chair Back Together
